Your Cart

All Products

All Products
Suggested Voltage:4.5V DC No load Speed:140rpm No Load Current:190mA(max.250mA) min Size:20*20*64There gear motors, 130 model, 140 model, 260 model, 280 model and many other micro-motors, please consult contact!Use: There are scientific electronic products, electric robot body type..
Wires,10cm. male-male,1p(pack) 1 pack=100pcs If no special requirements,the color will be picked randomly. ..
Arm length: 21cm2 servos: RA001B(S06NF STD servo) 1pc +RA001C (S05NF STDservo) 1PC..
WheelOuter diameterΦ78mmInner hole connects to servos,another connects to DG01D or DG02S motorThis wheel match with all DG01D and DG02S serial or ServoThe chassis with these wheels:..
Encoders use custom made 8-pole magnets and 2 haff-effect sensors to provide 2 square waves, 90 degree out of phase with a total of 16 state changes per motor revolution. These encodoers can operate with both 3.3V and 5V logic sustems and have reverse polarity protection built into the sensors. And..
DESCRIPTION: The T’Rex controller from DAGU is an Arduino compatible robot controller designed to power and control servos and brushed motors. This controller combines an Arduino development board with a dual FET H-bridge motor driver. The heart of the board is an ATMega328P AVR microcontroller whic..
Discharge method: hot melt extrusion moldingForming method: Three-dimensional moldingPrint range: unlimitedSpinning speed: adjustableTemperature: 80℃-195℃ AdjustableEquipment working voltage: 5V 2ANozzle diameter: 0.7mmComsumable diameter: 1.75mmCompatible with high and low temperature dual mod..
Support 3D printer teaching materialsDiameter: 1.75mmSpecifications: 0.6kg/volumeDensity: 1.24g/cm3Melt index: 5g/10min(190℃/2.16kg) or betterTensile strength is at least 65MpaBending strength is at least 87Mpa1 year warrantySafety specifications provide effective safety inspection report copies wi..
Product Parameters: ATmega2560 16MHz CPU 256K flash memory, 8K SRAM and 4K EEPROM USB interface and ISP socket (CP2102)  Built in 3A switch mode power supply 70 I/O pins with male and female headers Support for up to 48 servos 16x 10bit analog inputs 15x 8bit PWM outp 1xI2C ..
Specification:outer dia:48mminner dia:4mmthickness:20mmPack with screws, no hub needed. One pack include:omni wheel  4pcs M3*20mm copper pipe 4pcsM3*25mm screw   4pcsM3*30mm screw   4pcstapping screw   4pcsThere are 4 sections in the wheel; each section has 3pcs rubber connecting each other by a 3*..
Arm length: 13cmwith MK IIrobotic claw2 servos: RA001C (S05NF STD) 2pcs..
Include: 2 wheels, 2 motors, 2 encoder kit, screwsEncoder type:  8-pole neodymium magnet and hall-effect sensorEncoder output: Open drain with short circuit protection Encoder voltage: 3V – 24V with reverse polarity protectionEncoder resolution: 8 state changes / revolution when mounted on the outp..
Wires,10cm.female-female,1p(pack) 1 pack=100pcs  If no special requirements,the color will be picked randomly. ..
One, three-degree-of-freedom paw with servo protection & cushioning device2, short U PTZ bracket 13,3KG metal tooth steering gear 14, 13KG metal tooth steering gear 25, metal rudder 3!6, send a small wrench! !..
SpecificationsTracking bandwidth: 1.7CMPerimeter: 39.5.CM..
Showing 241 to 264 of 418 (18 Pages)